By Senior Technical Advisor at Elmatica, Jan Pedersen
What do you know about Bow & Twist Management? Read up with our Senior Technical Advisor Jan Pedersen.
The development of new components has always been the trigger to push PCB technology further up the ladder. Smaller and fine pitch footprints of SMT components challenge the PCB makers to achieve High-Density Interconnections, higher pattern accuracy, and improved flatness. Sometimes the PCB itself becomes an SMT component that shall be soldered to a bigger PCB, which will increase the requirements further.
As a result of the requirements of either component or that the PCB itself becomes an SMT component, Elmatica has been challenged by several of our customers for improved flatness and to avoid bow and twist under or after assembly. This has driven both Elmatica and a selection of our suppliers further, and challenged what we can call “bow and twist management”.
We can divide the root causes for bow and twist into two groups: Intrinsic and extrinsic bow and twist.
Intrinsic bow and twist have been inducted into the PCB during the lamination cure steps, and there are no corrective actions with the permanent effect!
Extrinsic bow and twist have been induced after the lamination cure steps, and corrective actions can be taken.
Production related intrinsic reasons:
1) Lamination press malfunction
2) Cross plying prepreg or inner layers – warp and fill directions must be same
3) Wrong glass ply construction used (Prepreg or Cores)
4) Missing or extra prepreg glass ply
5) Weave distortion (Cores or Prepreg)
6) Not fully cured inner layers
Design related intrinsic reasons:
1) Non-symmetric build (Prepreg and/or Cores)
2) Unbalanced copper distribution
- a) Layer to layer copper weights
- b) Within layers causing low-pressure areas
3) Core constructions
4) Breakaway area not matching copper distribution per layer.
Extrinsic bow and twist:
1) Mechanical deformation
3) Heat during solder mask or legend cure step.
4) HASL process
5) PCB assembly process
Some further comments to the breakaway area:
The copper pattern design of the breakaway area must mimic the copper distribution for each layer. A perfectly balanced breakaway area will move differently than the none perfect board itself and cause stress leading to a twist in the panel until we separate the PCB from the breakaway area.
Bow and twist test procedures
The PCB manufacturer shall perform tests during the production process to avoid intrinsic bow and twist. When the PCB arrives at the customer side with too much bow and twist, it is important to verify if the root cause is intrinsic or extrinsic. We recommend the following procedure:
1) Measure bow and twist by IPC TM650 2.4.22
2) Bake the boards 10 degr. Higher than the material Tg for 20 minutes, flat, side by side with no pressure or touching.
3) Cool the boards to room temperature at 1 degr. per minute leaving the oven door closed.
4) Measure again bow and twist by IPC TM650 2.4.22
5) The delta of bow and twist is now the degree of the intrinsic and extrinsic mix.
- If the boards become totally flat, the root cause is all extrinsic
- If the boards stay the same, the root cause is all intrinsic
- Any between is a mix.
How to measure Bow and twist?
Bow and twist improvements
When we shall look into improvements of bow and twist exceeding normal tolerances, we need to review the intrinsic root causes and tune both design and production-related issues that could affect the performance. First of all, we have to control that all related production processes are in control. Then we need to review potential improvements in the production process that could bring the performance beyond standard expectations.
The lamination is normally tuned to be cost-effective and still meet specified tolerances. The pressing cycle can be tuned further by extended cycle times to achieve improved performance.
Prepreg and inner cores:
The use of prepreg is a trade-off between customer specifications and the optimal choice for high performance. To give improved stability, the build must be 100% symmetric, and we need to choose the most robust prepregs and core constructions. The result will probably affect the impedance that needs to be recalculated.
The copper distribution must be optimized within each layer and should be matched within the build. The build must be symmetric and all pairs of layers on each side of the building center should have equal copper weight. (fig. 1).
Most designs with high layer counts will have a tendency of low-pressure areas. This could be avoided by adding copper filling by dummy pads or cross-hatched copper.
Split ground planes
Many PCB designs have so-called split planes that may perform as a bend indicator line, especially if we have the same pattern in more than one layer through the build.
The breakaway area is maybe the most neglected reason for bow and twist. It is essential for the performance that the copper on every layer of the breakaway area mimics the copper of the PCB itself.
Bend and twist management for improved performance is difficult and includes all the above-mentioned issues. It may require a number of sample runs to detect which if the actions that give the required effect. In addition, there are a number of actions that could be taken in the soldering and assembly process to improve flatness.
Together with our professional manufacturers, Elmatica has the experience and knowledge to guide our customers to achieve better performance. For such issues, you can contact your dedicated sales contact, who will request assistance from one of our application engineers.